How to Repair a Pipe That Is Broken Inside of a Wall

Homeowner will have a world of difficulty on their hands if their pipes burst. The good news is that they can be fixed, and the problems that led to their damage can be avoided.
You could do the task if you had the appropriate tools, the necessary expertise, and an understanding of the blueprint for your house.

What Are the Reasons That Pipes Burst?

Extremely cold weather is the most common factor that contributes to pipes breaking. Because of this, the water that is contained within them will swell and approach the freezing point.

When the pressure is allowed to build up to an unsafe level, the pipe’s framework begins to deteriorate. When the temperature drops to -6 degrees Celsius, this phenomenon typically takes place.

What Are the obvious  Signs That a Pipe Has Burst?

Depending on the location and severity of the pipe rupture, the telltale symptoms of a broken pipe may not be noticeable at all or they may be scattered all over the place. The word “water” will always be included on the placards.

Flooding.

The most evident evidence that you are experiencing a flood is if you find puddles of water on the floor, if the walls are very wet, and if the water meter is spinning erratically. If any of these conditions are present, then you are experiencing a flood.

Walls that are bubbling.

When the water damage caused by the leak is not immediately apparent, you may observe the formation of bubbles under the paint or wallpaper on your walls.

Mould

Another indication of an excess of moisture. Mold is a problem that can be found in certain homes regardless, but if it hasn’t been a problem in your home for a long and suddenly started, the likely culprit is a pipe that has burst.

Places in the grass that are noticeably greener.

In the event that a pipe had burst outside of your home and around your yard, water would be gushing all over your grass. And if there are areas of the lawn that are unusually green, the problem is typically a broken pipe.

Also read:

Electric Water Heater Repairs: What You Need to Know

How to Repair a Pipe That Is Broken Inside of a Wall

Because repairing a pipe that is located inside a wall is not a simple process, it is strongly recommended that you let a licensed plumber handle this problem. However, if you are confident that you can do the task on your own, simply follow the steps below.

• Utilizing a saw, remove broken pieces of drywall from the wall. After you have determined with absolute certainty where the damage is situated, create a hole in the wall so that you may gain access.
• Cover the pipe with a sheet and continue to move around until the sheet becomes wet. In the event that you do not have the good fortune to view the breakage with your own eyes, you will need to use a piece of cloth to locate it. It’s possible that you’ll need to do this a few times before you can zero in on the precise location of the crack.
• Put a container underneath the pipe that is broken. Because you are about to operate on a pipe, the plumbing repair is going to be filthy; therefore, the container should catch anything that drips or spills from the pipe.
• Remove the section of pipe that is leaking. For this, you will need to make use of a tool that cuts pipes. Tighten the screw on the tool, then rotate it until the pipe is completely cut through.
• Clean and dry the pipe. If it is raining, you will not be able to work.
• Use the pipe cutter once again to make a cut above the leaking area.
• Clear out the conduit. This pertains to both the interior and exterior of the building. Because the interior may contain additional ice, you should make sure that it is free of any impediments.
• Install a repair sleeve made of copper. Employ a blowtorch to heat the end of the repair sleeve that is located at the bottom.
• Give the solder time to melt and fill the junction before proceeding. After it has cooled down, which should take around ten minutes, repeat the process with the upper end. When you are doing this, make sure to wear gloves and safety goggles.
• After you are finished, make sure there are no leaks.
• Make repairs to the wall.
• If all these steps are not doing anything then it is better to call a local plumber you can trust who have expertise with burst pipes.